The writer is making a number of good points on the subject of Tools You Need to Install a New Bathtub as a whole in this post following next.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and often, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably tough task. If the old tub is easily available, the task can move rapidly; if you need to open a wall surface to get rid of the old bathtub and position the brand-new bath tub, the job is much harder. In either case, the job is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and also set in the new one. Ensure you have actually certified on your own for the job and are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed project, it is much better to think about utilizing one prior to you start. Opportunities are you might require a professional plumber to make tube connections.
This article will help you set up a new tub in your shower room if you have already purchased a new tub as well as don't need to alter the plan of your previous water system pipelines.
Your tools as well as material checklist ought to make up the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be quite bothersome because of the restricted access that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in location in between the faucet and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the bath tub until the spirit level checks out degree.
To mount taps, fit the bottom of the outermost adaptable faucet connector to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Activate the supply of water as well as examine all joints and also new pipework for leaks as well as tighten them if essential. Load the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leakages.
Lastly, deal with the bath paneling as described in the producer's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been utilized a minimum of when as this will certainly resolve it right into its last placement.
Preparing for the Installation
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its final setting.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your components as well as installations. They are sold in tubes and also cartridges, and can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealant can fracture fairly very early if you do not take into account this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently available on the market. It is suggested to fit the tiles utilizing waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on Tools You Need to Install a New Bathtub ? Place a remark down the page. We would be glad to find out your responses about this blog entry. We are looking forward that you come back again before long. So long as you enjoyed reading our page please remember to share it. I am grateful for your time. Please stop by our website back soon.
Visit My Website